High Strength 1:1 Two-Component Polyurethane Liquid Rubber For
Making Wall Tile Concrete Stamping Molds
Description
Polyurethane liquid rubber consists of A&B component, B is
curing agent, and A is polyurethane prepolymer.
can be used as a concrete or cement stamping mold as well as for
making hard durable rubber parts for machinery or automotive
applications.
There are many different formulations of polyurethane rubbers for
mould making. The polyurethane casting rubber can be pure or filled
with special mineral charges. Are available different hardness from
40 Shore A to 80 or 90 Shore A.
Applications
Substitute for making the mould of “cultural stone” and concrete
stamping. It also applies to electrical equipment potting, rubber
rollers, Ski and snowboard ,rubber plates, rubber wheels, shoe
models and others.
Properties of Liquid Polyurethane Rubber for Making Concrete GRC
Molds:
Technical Datasheet
A | Type | MC-PU70A |
| Appearance | Colorless or light yellow transparent liquid |
| Viscosit(y 30℃)mPa·s/ | 2500±300 |
B | Type | MC-PU70B |
| Appearance | Light yellow liquid |
| Viscosity(30℃)/mPa·s | 560±200 |
| Ratio A:B(mass ratio) | 1:1 |
| Operation temperature/℃ | 25-40 |
| Gel time(30℃)*/min | 20-30(variable) |
| Appearance | Light yellow |
| Hardness (shore A) | 70±3 |
| Tensile strength/MPa | 8-11 |
| Elongation at break/ % | 250-350 |
| Tear strength/(kN/m) | 26-30 |
| Rebound/ % | 30-35 |
| Specific gravity(25℃)(g/ cm3) | 1.18 |
Features
Fluid liquid
Cold curing
Easy to use
No linear shrinkage
Excellent mechanical resistance
High tearing strength
Long life of the moulds
Measuring & Mixing
Liquid urethanes are moisture sensitive and will absorb atmospheric
moisture. Mixing tools and containers should be clean and made of
metal or plastic. Materials should be stored and used in a warm
environment (23°C-25°C).
IMPORTANT: Stir Part B thoroughly before dispensing. After
dispensing equal amounts of Parts A and B into mixing container,
mix thoroughly forat least 3 minutes making sure that you scrape
the sides and bottom of the mixing container several times.
Packaging
20kg per drum, 640kg per pallet
Storage
Store in cool and dry place. If you can’t use one drum up at a
time, please inject N2.The storage time of original packing is 6 months.
Tips:
Always wear a respirator or self –contained breathing apparatus
when working with urethanes.
Use between 65F and 75F in a humidity-controlled environment.
AeroMarine Products Concrete Molding and Stamping Rubber 75A
Urethane is moisture sensitive.
Use only clean plastic and/or metal mixing utensils and containers.
Do not use paper or wood.
Re-cap the bottles immediately after use.
Extend-It aerosol nitrogen blanket can be used to protect the
product from moisture contamination.
Never mix less than about 3 ounces of product, as this ratio is
hard to measure and will take longer to cure as the exothermic
reaction does not generate much heat at this volume.
Avoid mixing with drill motors because of the friction they
generate, mixing with electric drills can start the exothermic cure
process and cause the product to cure in the mixing container.
It is always best to mix the material by hand, with a plastic or
metal mixing utensil.
Don’t vary the mix ratio. Unlike some polyester resins, altering
the mix ratio to vary the cure cycle will not work with urethanes.
Mix in clean plastic containers. Paper cups and wooden mixing
utensils may contain moisture which can adversely affect the
urethane rubber. Avoid waxed paper cups because the wax may melt
and contaminate the rubber.
Air bubbles in urethanes are almost always caused by moisture. Do
everything possible to avoid moisture getting into the mix. Replace
the lids onto the containers promptly after use. Do not use the
urethane rubber during rainy days or times of high humidity. Avoid
pouring against an unsealed water based product such as plaster or
hydrocal. Seal plaster or hydrocal with a product like Krylon Clear
Acrylic.
Avoid mixing a large batch- The larger the batch, the more exotherm
or heat is generated in the cure cycle. If you are making a large
mold, mix small batches to make the process more manageable.
Shake or stir well before use- The liquid components may settle in
the containers during storage. Shake or stir the components
separately and thoroughly before mixing. Let it sit a few minutes
to let any bubbles rise to the surface after shaking the container.
